Short answer: an AQL inspection does not prove a batch is good; it bounds the probability that a bad batch gets through. The number that matters is not the AQL figure but the defect classification — what counts as critical, major and minor for a cosmetic.
Buyers often arrive at inspection with a single number in mind: AQL 2.5, general level II, done. That is a reasonable default and it is also where most disputes start, because two inspectors can apply the same AQL to the same lot and reach different verdicts if nobody agreed in advance what a "major defect" is on a cream jar.
This guide covers the sampling arithmetic, the defect classes that fit cosmetics, when to inspect, and what to do when the lot fails.
What AQL actually is
AQL — acceptance quality limit — is defined in ISO 2859-1 as the quality level that is the worst tolerable process average when a continuing series of lots is submitted for acceptance. It is a property of a sampling plan, not a promise about a product.
Three consequences follow:
- It is a risk statement. A plan with AQL 2.5 and a sample of 125 accepts lots whose true defect rate is around 2.5% most of the time — and rejects some lots that are better than that, and accepts some that are worse.
- It assumes a series of lots. A single pre-shipment inspection is a one-off application of a plan designed for ongoing supply. That is why the result is evidence, not proof.
- The defect classification carries the plan. If a leaking pump is classified as "minor", the plan will accept a lot with a lot of leaking pumps. The classification is the substantive decision.
The sampling arithmetic
For general inspection level II — the normal default for consumer goods — the sample size and acceptance numbers for the common lot sizes are:
| Lot size | Code letter | Sample size | AQL 2.5 (Ac / Re) | AQL 4.0 (Ac / Re) |
|---|---|---|---|---|
| 501–1,200 | J | 80 | 5 / 6 | 7 / 8 |
| 1,201–3,200 | K | 125 | 7 / 8 | 10 / 11 |
| 3,201–10,000 | L | 200 | 10 / 11 | 14 / 15 |
| 10,001–35,000 | M | 315 | 14 / 15 | 21 / 22 |
Ac is the number of defects that still allows acceptance; Re is the number that rejects. A lot with 8 major defects at n=125 is rejected at AQL 2.5 and accepted at AQL 4.0 — which is why the AQL figure is a negotiation, and why it should be written into the purchase order rather than agreed at the inspection.
For cosmetics, a common split is AQL 2.5 for major defects and AQL 4.0 for minor ones, with critical defects at zero acceptance regardless of the sample size.
Defect classes that fit a cosmetic
Generic inspection checklists are written for electronics and apparel. A cosmetic lot needs its own classification, and it should be agreed before the first inspection, not after a failure.
| Class | Definition | Cosmetic examples |
|---|---|---|
| Critical | Unsafe, illegal, or unusable; zero acceptance | Wrong product in the carton, missing batch code, microbial growth, leakage in transit packaging, label with the wrong market's language |
| Major | Reduces usability or saleability, or breaches the specification | Fill weight below tolerance, pump that does not dispense, cap that leaks, colour outside the approved tolerance against the Golden Sample, wrong cap colour |
| Minor | Cosmetic or cosmetic-adjacent, does not affect use | Scuffs on a carton, slightly off-centre label, print registration within tolerance, minor moulding flash |
Two classifications are worth arguing about explicitly, because they decide most outcomes:
- Fill weight. A net content shortfall is a legal issue in most markets, so it belongs in critical or major, not minor. The measurement method matters too — average net content versus individual unit minimum are different rules.
- Colour. "Within tolerance" has to mean a measured value against the approved standard, not an inspector's opinion. Colour difference measured against a retained Golden Sample, under agreed lighting, is the only defensible basis.
What an inspector should actually check
An inspection of a cosmetic lot usually takes one to two working days and covers:
- Quantity and carton count against the packing list.
- Product identity — artwork, language, batch code, expiry or PAO, barcode.
- Fill and net content — weighed or volumetrically checked, against the declared tolerance.
- Functional check — pump prime and dose, cap torque and removal, spray pattern, dropper delivery, trigger return.
- Seal integrity — leakage under inverted storage, induction seal condition where used.
- Appearance — colour and texture against the retained Golden Sample, odour check.
- Packaging integrity — carton print, insert presence, shipper condition, pallet pattern.
- Traceability — batch record availability, and whether the inspected goods can be tied to a batch number.
The functional check is where cosmetics differ from most consumer goods: a pump that works on unit 1 and fails on unit 20 is a systematic problem, and a 125-piece sample will find it if the check is performed rather than assumed.
When to inspect
The single most common scheduling error is inspecting too early. An inspection is meaningful when:
- Production is complete and 100% of the lot exists — not 80% with the rest "almost done".
- Primary packaging is complete for the sampled units, so the sample reflects the shipped configuration.
- The goods are in export cartons, because packaging defects are part of what is being assessed.
Inspecting mid-production samples tells you about the process, not about the lot. If you need process assurance, that is a different service — a during-production check — and it should be scheduled separately.
How inspection relates to the CoA and the factory's own checks
A certificate of analysis reports what the factory tested on the bulk: pH, viscosity, microbial count, sometimes preservative content. It does not report fill weight, pump function or label accuracy. The two are complementary:
- CoA — is the bulk within specification?
- AQL inspection — is the finished, packed lot within specification?
A lot can pass the CoA and fail inspection, and that combination usually points to the filling and packing line rather than the formula. Our filling and capping accuracy guide covers that boundary in detail, and the batch documents explainer covers what the CoA should contain.
When a lot fails
A failed inspection is not the end of a shipment; it is a decision point. The usual options, in order of preference:
- Sort and rework. The factory re-inspects 100%, removes defective units and replaces them, then a re-inspection samples the corrected lot. This works when the defect is contained and the deadline allows it.
- Accept with a deviation. Appropriate for minor defects where the buyer accepts a documented concession. It should be recorded, not agreed verbally.
- Reject the lot. The commercial consequences — rework, delay, cancellation — belong in the purchase order, not in the inspection report.
Whatever the outcome, the inspection report with photographs and defect counts is the document that makes the conversation possible. A report that says "quality not acceptable" without counts and images is not usable evidence.
The five mistakes buyers make
- Agreeing the AQL figure but not the defect classification. The classification decides the result.
- Inspecting before production is complete. The sample no longer represents the lot.
- Skipping the functional check. Pumps, caps and droppers are where cosmetics fail in the customer's hand.
- Judging colour by eye without a retained standard. Agree the lighting and the reference before the first inspection.
- Treating a pass as a guarantee. A sampling plan bounds risk; it does not eliminate it. For a first order, a retained sample from the inspected lot is worth more than the report.
FAQ
Q: What AQL should a first cosmetics order use? A: AQL 2.5 for major defects and 4.0 for minor defects at general inspection level II is a common starting point, with critical defects at zero acceptance. The classification matters more than the number.
Q: How many units are inspected in a 5,000-piece lot? A: At general level II the code is L and the sample is 200 units, with acceptance at 10 major defects and rejection at 11 for AQL 2.5.
Q: Can an inspection be done while production is still running? A: It can, but it then measures the process rather than the lot. A pre-shipment inspection should be scheduled when 100% of the goods exist and are packed in export cartons.
Q: Does a passed inspection replace a certificate of analysis? A: No. The CoA covers bulk specification tests such as pH, viscosity and microbiology; the inspection covers fill, function, labelling and packing. They answer different questions.
Q: What happens if the lot fails inspection? A: The usual routes are 100% sorting and rework with a re-inspection, a documented deviation for minor defects, or rejection. The purchase order should state which costs fall to which party.